Copyright © 2010 All Rights Reserved
Synforce Lubricants.
Synforce Lubricants.
Material Safety Data Sheets can be found for each product at the bottom of this page
Most equipment operators will relate to and understand that hydraulic failures can be costly, and are due in many instances to sub quality performance from the hydraulic oils, either causing premature wear or heat related failures.
With most oil companies selling Hydraulic oil on price (not quality), the quality is almost always questionable. The first way to making a cheap oil, is to skimp on additives and base oil quality.
As components in pumps etc are being designed with less tolerances now than in the past, and operating pressures are now relatively higher and from smaller pumps, a lot more is expected from the oil.
Synforce has produced a range of Hydraulic oils now recognised to be amongst, if not the best available in Australia, today.
Base Oils ... used in all our hydraulics are Group 2 Hydrocracked, renowned world wide to be the best, and guaranteed to perform better than other mineral oils under severe conditions.
Cleanliness ... Oil contamination is the biggest enemy of any equipment, and brings on early and expensive component failure. We have achieved "off the shelf" cleanliness ratings to which no other company that we know has been able to achieve, let alone boast.
Anti Wear overtreat ... this reduces wear significantly and leads to extended component life.
Viscosity Index ... The ability of the oil to stay in grade under both normal and severe operating conditions, and boast our oils to have the highest Viscosity Index of any hydraulic oil on the market in Australia today, that we know of.
Shear Stability ... Viscosity modifiers used in oils are quoted as having shear stability rating, expressed as SSI (Shear Stability Index), and the lower the rating number, the better the resistance to shear. We use only the best available Viscosity Modifiers with the lowest SSI
Synforce Hydraulics have the best available cleanliness rating, the highest anti wear protection, the highest ability to withstand the effects of viscosity change due to heat (Viscosity Index), and are made from only the most Shear Stable components available in Australia today, giving our product the best SSI available. No one does Hydraulics better than Synforce.
We forwarded this photo to a Lubrizol additives representative who in turn commented and we quote;
“The contamination is a gathering of the Polymer used in the lubricant as a result of the lubricant being poorly and almost certainly cold blended, Polymers do not mix as well in cold blended lubricants as opposed to hot blended lubricants”
We have always pushed our hot blend system as the ultimate method and have always quoted that polymers in cold blended lubricants can cause exactly this problem; the photo can only be seen as documented proof.
After cleaning the system etc. and refilling with Synforce product the machine began to operate correctly, the owner was lucky in this instance as significant damage to the transmission and hydraulics etc. could have easily occurred due to insufficient lubricant being available to moving parts, the filter was blocked to the point of allowing only a very small amount of lubricant to pass through it, had the owner operated the machine for much longer the result could have been disastrous.
It would be fair to say that all the “cheap” lubricants will suffer from this at some point and that can result in significant equipment damage
Polymers are used to create Multi-grade oils and it is commonly known throughout the lubricant manufacturing industry that they do not mix properly in a cold blend, they require blend temperatures of approx. 55 deg C and agitation for a suitable period of time to bond correctly and evenly throughout the finished product.
When Polymers are supplied to blenders they come in a very thick and sticky form, much thicker than say honey, and they require elevated temperatures to get them to “near liquid” form.
Standard Anti wear (AW range) ... ISO 22, 32, 46, 68 and 100 with typical viscosity indexes of 110 and pre-filtered through 3 micron absolute. All of our AW range have 400ppm Zinc Aitiwear offering better component protection.
Synforce AW Hydraulics meet or exceed; Vickers M2952-S , Denison HF-1, HF-2, HF-0 ... Cincinnati Milacron P68, P69, P70 , US Steel 127, 136 , Racine Vane Pumps – Variable volume
Ashless fluids ... Zinc free and Ashless to the latest requirements for Hydraulics and some Compressor oils in ISO 32, 46, 68 and 90.
Synforce Ashless Hydraulics are pre-filtered through 3 micron absolute and meet or exceed;
for Hydraulic fluids; Dennison HF-0, HF-1, HF-2 ... Cincinnati P-68, P-69, P-70 ... DIN 1524 part 2 & part 3 (HLP), HVLP) ... ISO 6743/4 (HM, HV) ... AFNOR NF E 48-603 (HM, HV) ... SS 155434 ... VDMA 24318 ... U.S. Steel 126, 127 & 136 ... AND
for Compressors oils according to; DIN 51506 (VBL, VCL, VDL) ... ISO DP 6521 (DAA, DAB, DAH, DAG)
High Viscosity Index (HVI range) ... ISO 32, 46, 68 and 100 with typical viscosity indexes of 156 and pre-filtered through 3 micron absolute. All of our HVI range have 400ppm Zinc Aitiwear offering better component protection.
Synforce HVI Hydraulics meet or exceed; Cincinnati Milacron P68, P69, P70 , DIN 51524 part 2 , Lee-Norse 100-1 , Jeffrey No 87 ... US Steel 127, 136 , Ford M6C32 , General Motors LH-04-1, LH-06-1, LH-15-1 ... Racine Vane Pumps - Variable Volume ... Commercial Hydraulics (except PMS500 Series) AFNORE48-603
Series 7000 Harvester Hydraulic fluid is a new generation Hydraulic Oil employing superior Group 2 Hydrocracked base oils and the latest anti-wear technology for use in applications of extreme shear and wide temperature range encountered in mining, agriculture, industrial and precision hydraulic control systems, where minimal change in viscosity with temperature and very high shear stability is required.
Synforce Series 7000 is especially recommended for severe applications such as Austoft 7000 and Camaco Cane Harvesters where the hydraulic oil is highly stressed, providing maximum “cold start” protection and superior “air release”, ensuring minimal wear to pumps and motors.
Cleanliness;
Synforce Series 7000 is pre-filtered through 2 micron absolute filtration during the manufacturing process ensuring Series 7000 to be the “cleanest off the shelf” Hydraulic oil available.
Series 7000 meets or exceeds; Vickers 1-286-S, M2952-S … Denison HF-1, HF-2, HF-0 … Cincinnati Milacron P68, P69, P70 DIN 51524 part 2, … Lee-Norse 100-1 … Jeffrey No 87 … US Steel 127, 136 … Ford M6C32 ... General Motors LH-04-1, LH-06-1, LH-15-1 … Racine Vane Pumps – Variable Volume ... Commercial Hydraulics (except PMS500 Series) AFNORE48-603
vHVI Hydraulic fluids ... are a range of Ashless, ZINC FREE, very high viscosity index, very high performance antiwear hydraulic oils formulated on superior Group 2 base oils that is specifically designed to meet the needs of modern, high pressure, hydraulic systems and Rotary Screw compressors.
vVHI Hydraulic fluids exhibit exceptional oxidation and thermal stability allowing long oil life and minimized deposit formation in severe hydraulic systems using high pressure, high output pumps
* Very high oxidation stability (extended service life) * High load carrying capacity
* Excellent demulsification
* Excellent corrosion protection against steel and non-ferrous metals
* Excellent filterability
* Excellent thermal and hydrolytic stability
Applications
* Hydraulic systems operating at high pressures and high temperatures in critical applications.
* Hydraulic systems subject to deposit build-up such as sophisticated Computer Numerically
Controlled (CNC) machines, particularly where close clearance servo-valves are used
* Systems where cold start-up and high operating temperatures are typical
* Systems requiring a high degree of load-carrying capability and anti-wear protection
* Machines employing a wide range of components using various metallurgy
* Rotary screw compressors in natural gas service
vHVI 46 Hydraulic fluid meets or exceeds; Dennison HF-0, HF-1, HF-2 ... Arburg ...Cincinnati P68, P69, P70 Bosh-Rexroth RE 90220-01 ... JCMAS HK-1 ... DIN51524, HLP part 2 and HVLP part 3 ... ISO 6743/4 (HM, HV) VDMA 24318 ... Eaton Vickers; M2952S, I-1286-S, M-2950-S ... AFNOR NF E 48-603 (HM, HV) ... SS 155434 ....U.S. Steel 126, 127 and 136 ... Krauss-Maffei Kunststofftechnik
and Compressor oils according to;
DIN 51506 (VBL, VCL, VDL) ... ISO / DP 6521 (DAA, DAB, DAH, DAG)
also available in ISO grades 22, 32, 46, 68 and 100
| Attachment | Size |
|---|---|
| Ashless 32 SDS-221.pdf [1] | 229.22 KB |
| Ashless 46 SDS-221.pdf [2] | 229.28 KB |
| Ashless 68 SDS-221.pdf [3] | 229.38 KB |
| Ashless 90 SDS-221.pdf [4] | 229.26 KB |
| AW 22 SDS-221.pdf [5] | 228.87 KB |
| AW 32 SDS-221.pdf [6] | 228.81 KB |
| AW 46 SDS-221.pdf [7] | 229.35 KB |
| AW 68 SDS-221.pdf [8] | 229.91 KB |
| AW 100 SDS-221.pdf [9] | 228.58 KB |
| HVI 32 SDS-221.pdf [10] | 228.6 KB |
| HVI 46 SDS-221.pdf [11] | 229.43 KB |
| HVI 68 SDS-221.pdf [12] | 229.32 KB |
| HVI 100 SDS-221.pdf [13] | 228.13 KB |
| vHVI 68 SDS-221.pdf [14] | 228.16 KB |
Links:
[1] http://synforce.com.au/sites/default/files/Ashless 32 SDS-221.pdf
[2] http://synforce.com.au/sites/default/files/Ashless 46 SDS-221.pdf
[3] http://synforce.com.au/sites/default/files/Ashless 68 SDS-221.pdf
[4] http://synforce.com.au/sites/default/files/Ashless 90 SDS-221.pdf
[5] http://synforce.com.au/sites/default/files/AW 22 SDS-221.pdf
[6] http://synforce.com.au/sites/default/files/AW 32 SDS-221.pdf
[7] http://synforce.com.au/sites/default/files/AW 46 SDS-221.pdf
[8] http://synforce.com.au/sites/default/files/AW 68 SDS-221.pdf
[9] http://synforce.com.au/sites/default/files/AW 100 SDS-221.pdf
[10] http://synforce.com.au/sites/default/files/HVI 32 SDS-221.pdf
[11] http://synforce.com.au/sites/default/files/HVI 46 SDS-221.pdf
[12] http://synforce.com.au/sites/default/files/HVI 68 SDS-221.pdf
[13] http://synforce.com.au/sites/default/files/HVI 100 SDS-221.pdf
[14] http://synforce.com.au/sites/default/files/vHVI 68 SDS-221.pdf